Acro Naze32 Flight Controller

AfroFlight Naze32 Rev6 Flight Controller (Acro)

hobbyking.com

Designed for serious quad racers and freestyle maniacs, the AfroFlight Naze32 flight controller is undeniably the most used, recognised and supported flight controller in the scene today. With a 32bit ST micro processor and a host of equally impressive sensors, this Rev6 Acro version comes with 16mbit memory and the BMP280 barometer. This board also comes with angled header pins and is configurable with baseflight / Cleanflight via the onboard USB connector. Features: • USB on right side • PPM/PWM input as through-hole • Flexible motor outputs, support various airframe types: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. Note: Our Naze32 Rev6 boards are hand crafted in a secret location deep inside Mount Tsubakuro by Timecop and his legions of SMT Ninja henchmen. Ok, we made that bit up, but they are the real deal and manufactured in Japan. Classic FC, great for beginners and easy to set up. You wont get the features of other boards like extra UART ports but this is great at the current price ($17 USD). A classic FC, great for beginners and easy to set up. You don't get the features of other boards like extra UART ports but it's pretty good at the current price ($17USD).

AfroFlight Naze32 Rev5 Acro FunFly Controller

hobbyking.com

The infamous Hamasaki AKA “timecop” was not happy with the limitations and performance an 8-bit MCU could deliver on current FC platforms, so he set out to make a flight controller that could take just about any demands a developer could throw at it, and thus was born the Naze32. At the heart of the Naze32 is a 32bit ST micro work horse of a processer, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. The Naze32 comes as the most complete Acro Version yet, with both strait and 90deg pins for your preference and a matched break out harness. Great Flight Controler! I had a cc3d atom before, i flashed both of them to cleanflight and flew them in the same copter, so i could compare them. At first I noticed, that the naze32 semms to work a lot faster! It connects much faster to my cleanflight software than my cc3d did before. I might change that, since with the bluetooth dongle (and the comment under the video of Project BlueFalcon on youtube), no USB connection is needed anymore. Great thing to start, after a while some minor drawbacks can be seen, but altogether a very useful first flight controller. Great flight controller. Works just fine, great price and easy to program.

Acro Naze32 Flight Controller rev6 (w/ pin headers)

www.getfpv.com

The FunFly Controller Acro Naze32 rev6 flight controller by AbuseMark. The newest version, rev6, of the popular Acro Naze32 flight controller board by AbuseMark. At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration.

AfroFlight Naze32 Rev 5 Acro FunFly Controller - Soldered version ...

hobbyking.com

The infamous Hamasaki AKA “timecop” was not happy with the limitations and performance an 8-bit MCU could deliver on current FC platforms, so he set out to make a flight controller that could take just about any demands a developer could throw at it, and thus was born the Naze32. At the heart of the Naze32 is a 32bit ST micro work horse of a processer, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. The Naze32 comes as the most complete Acro Version yet, with pre-soldered strait pins for your preference and a matched break out harness. This is the 6 dof version, without 3-axis magnetometer (HMC5883L) Barometric Pressure sensor (MS5611). thiese chips is missing on the board, you dont get heading hold, altitude hold flight mode If you need that. I use it for a 250 quad for acrobatic, easy to install with Cleanflight ... Nice n shiny finish, good covering. Fantastic item, I use it all the time in all places and electronics. ... Naze32 is the best that has ever happened to me, flight is impressive, no PID tunings required for me, I dumped my old kk2.1 and will never buy again, Naze32 is the best, some people say that it's for acro only, that is so wrong, acro and self level are both equally awesome, almost feels like a unit with GPS, almost... AfroFlight Naze32 Rev 5 Acro FunFly Controller - Soldered version (Vertical Pin)

Naze32 F3 Flight Controller Acro 6DOF Betaflight Cleanflight Full ...

speedyfpv.com

Naze32 Acro Flight Control NAZE32 Upgrade Version Specifications: Version: Acro 6DOF 36x36mm board, 30.5mm mounting holes. STM32F3 CPU. High-capacity Flash MPU6050 Accelerometers and Gyroscopes MicroUSB socket. 4x 4 pin JST-SH Socket (I2C, SWD, 2xuart) 2x 8 pin JST-SH Socket (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND Product Type: Flight Controller Brand: SpeedyFPV BEC: No Configuration: Standalone CPU: F3 Mounting: 30.5x30.5 OSD: No · Naze32 Acro Flight Control NAZE32 Upgrade Version Specifications:

AfroFlight Naze32 Rev5 Acro FunFly Controller - Soldered version ...

hobbyking.com

The infamous Hamasaki AKA “timecop” was not happy with the limitations and performance an 8-bit MCU could deliver on current FC platforms, so he set out to make a flight controller that could take just about any demands a developer could throw at it, and thus was born the Naze32. At the heart of the Naze32 is a 32bit ST micro work horse of a processer, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. The Naze32 comes as the most complete Acro Version yet, with both pre-soldered 90deg pins for your preference and a matched break out harness. First I did flash to beta flight 3.1.7 with no issues and it runs ok, but only upto 1.3k Hz Being a noob I was misled by the "rev 5" thinking it was F5 as in >F3. As of June 2017, I will suggest you need an F3 to run 2kHz control loops. Also, it was rather a pain desoldering the pin headers which interfered with my stack. Be warned. Might look like a good price, but perhaps you should look elsewhere. ... Naze32 as always is super. Love the board it is way better than kk 2.1 I spent hours setting the kk2.1 up. I spend maybe 20 min. max and was up and flying it is way better than kk2.1. The Naze32 is the go to board. The only problem I had when setting it up was my windows 10 64 bit computer was not recognizing it.